Thursday, May 19, 2011

Campbell Hausfeld Air Compressor Introduction, Safety Guidelines, Setting Up Your Unit, and Maintenance Tips

We’ve captured some of the highlights of the operator’s manual for the CE line of air compressors by Campbell Hausfeld. We hope this is a helpful resource for you if you have any questions about such topics as related to your unit.

The Campbell Hausfeld CE Series air compressors are two stage, oil lubricated reciprocating compressors. Among the compressors we carry are the CE6000, the CE7050, the CE7000. (The CE7050 and CE7000 are also available as “full package” options or automotive seies. See more below.)  There are two configurations:

Shop Air Series (basic) and Automotive Series Compressors (fully packaged).
Shop Air Models Include:
  • Compressor pump
  • ASME air receiver with safety valve
  • Electric Motor or gas engine
  • Starter
  • Pressure switch
Automotive Series Models Include:
  • All of the features of the Shop Air models
  • Digitial hour meter
  • Air cooled aftercooler
  • Automatic tank drain
  • Low oil guard
  • Vibration isolation pads
  • Shut off valve
Quick Reference
Recommended Oil (2 options)
-Single viscosity SAE 30 IS100 nondetergent compressor oil.
-10W30 synthetic oil such as Mobil 1

Oil Capacity
CE7000 Series: 2 Quarts
CE8000 Series: 4 Quarts

SAFETY GUIDELINES

DANGER sign indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING sign indictates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
CAUTION sign indictates a potentially hazardous situation which, if not avoided, MAY result in death or serious injury.
NOTICE sign indictates important information, that, if not followed, may cause damage to equipment.

IMPORTANT SAFETY INFORMATION
Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc) used make up a high pressure pumping system, the following safety precautions must be observed at all times.

GENERAL SAFETY
  • Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper use of the equipment.
  • Follow all local electrical and safety codes as well as the United States National Electric Codes (NEC) and Occupational Safety and Health Act (OSHA).
  • Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.
  • Keep visitors away and NEVER allow children in the work area.
  • Wear safety glasses and use hearing protection when operating the unit.
  • Do not stand on or use the unit as a handhold.
  • Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness, or leakage. Repair or replace defective items before using.
  • Check all fasteners at frequent intervals for proper tightness.
  • Keep fingers away from a running compressor; fast moving and hot parts will cause injury and / or burns.
  • If the equipment should start to vibrate abnormally, STOP the engine /motor and check immediately for the cause. Vibration is generally an indication of trouble.
  • To reduce fire hazard, keep engine /motor exterior free of oil, solvent, or excessive grease.
NOTICE: Drain liquid from tank daily.
Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and inspect periodically for unsafe conditions such as rust formation and corrosion. Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system.

SPRAYING PRECAUTIONS
  • Do not smoke when spraying paint, insecticides, or other flammable substances.
  • Use a face mask / respirator when spraying and spray in a well-ventilated area to prevent health and fire hazards
  • Do not direct paint or other sprayed material at the compressor.
  • Locate compressor as far away from the spraying area as possible to minimize overspray accumulation on the compressor.
  • When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer.
UNPACKING
After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for loose, missing, or damaged parts. Check to be sure all supplied accessories are enclosed with the unit.

REQUIRED ITEMS (not included)
  • oil
  • vibration isolator pads (Shop Air Series only)
INSTALLATION
Picking the location
Install and operate unit at least 18″ from any obstructions in a clean and well-ventilated area. The air temperature should not exceed 100 degrees farenheit. This will ensure an unobstructed flow of air to cool the compressor and allow adequate space for maintenance.

CAUTION: Do not locate the compressor air inlet near steam, paint spray, sandblast areas, or any other source of contamination.

Note: If compressor operates in a hot, moist environment, supply compressor pump with clean, dry outside air. Supply air should be piped in from external sources.

Tank Mounting
The tank should be bolted into a flat, even concreate floor or on a separate concrete foundation. Vibration isolators should be used between the tank leg and the floor. Model MP349500AJ isolator pads are recommended for horizontal units. Model MP345700AJ isolator pads are recommended for vertical units. Isolator pads are included with fully packaged models. If you are in need of isolator pads, please call Clark at 603-234-2612.

When using isolator pads do not draw bolts tight. Allow the pads to absorb vibrations. When isolators are used, a flexible hose or coupling should be installed between the tank and service piping.

WARNING: Failure to properly install the tank can lead to cracks at the welded joints and possible bursting.

PIPING
Any tube, pipe, or hose connected to the unit must be able to withstand the temperature generated and retain the pressure. All pressurized components of the air system must have a pressure rating of 200 psi or higher. Incorrect selection and installation of any tube, pipe, or hose could result in bursting and injury. Connect piping system to the tank by using the same fitting as the discharge port.

INSTALLING A SHUT-OFF VALVE
A shut-off valve should be installed on the discharge port of the tank to control the air flow that flows out of the tank. the valve should be located between the tank and the piping system.

WARNING: Never install a shut-off valve between the compressor pump and the tank. Personal injury and equipment damage may occur. Never use reducers in discharge piping.

When creating a permanently installed system to distribute compressed air, find the total length of the system and select pipe size from the chart. Be sure to bury underground lines below the frost line and avoid pockets where condensation can gather and freeze.

Apply air pressure to the piping installation and make sure all joints are free from leaks BEFORE underground lines are covered. Before putting the compressor into service, find and repair all leaks in the piping, fittings, and connections.

WIRING
Wiring must be installed in compliance with National Electrical code and local codes and standards that have been set up covering electrical apparatus and wiring. These should be consulted and local ordinances observed. Be certain that adequate wire sizes are used, and that:

1. Service is of adequate ampere rating.
2. The supply line has the same electrical characteristics (voltage, cycles and phase) as the motor. Refer to motor name plate for electrical ratings and specifications.
3. The line wire is the proper size and that no other equipment is operated from the same line. The chart gives minimum recommended wire sizes for compressor installations.

GROUNDING
This product MUST be grounded. Grounding reduces the risk of electrical shock by providing an escape wire for the electric current if short circuit occurs. this product must be installed and operated with a power cord or cable that has a grounding wire.

BREAKERS AND FUSES
The entire electrical system should be checked by a certified electrician. Time delay breakers and fuses may indicate a direct short to ground, high current draw, improper wiring, incorrect fuse or breaker size and/or type. This needs to be evaluated by a certified electrician.

COMPRESSOR LUBRICATION
Add oil as required. The oil and oil filter should be changed every 3 months or after every 500 hours of operation; whichever comes first. If the compressor is operated under humid conditions for short periods of time, the humidity will condense in the crankcase and cause the oil to look creamy. Oil contaminated by condensed water will not provide adequate lubrication and must be changed immediately. Using contaminated oil will damage bearings, pistons, cylinders and rings and is not covered under warranty. To avoid water condensation in the oil, periodically run the compressor with tank pressure near 150 psi for two stage compressors or 120 psi for single stage compressors by opening the drain cock or an air valve connected to the tank or hose. run the pump for an hour at a time at least once a week or more often if the condensation reoccurs.

IMPORTANT: Change oil after first 50 hrs of operation

AIR FILTER
Never run the compressor pump without an intake air filter or with a clogged intake air filter. The air filter element should be checked monthly.
Operating compressor with a dirty air filter can cause high oil consumption and increase oil contamination in the discharge air. If the air filter is dirty, it must be replaced.

INTERCOOLER
Check the intercooler weekly to be sure all fittings are secure and tight. Clean all dirt, dust and other accumulations from the intercooler fins.

COMPONENTS
Turn off all power and clean the cylinder head, motor, fan blades, air lines, intercooler, and tank on a monthly basis.

BELTS
Check belt tension every three months. Adjust belt tension to allow 3/8″ to 1/2″ deflection with normal thumb pressure. Also, align belts using a straight edge against the face of the flywheel and touching the rim on both sides of the face. The belts should be parallel to this straight edge. Dimension A should be the same as B and C to ensure proper alignment of the belts. Slots in the bedplate allow you to slide the motor back and forth to adjust belt tension.

We hope these highlights from the operator’s manual have been helpful to you. We aim to post a Troubleshooting Guide as well, to give customers easy access to finding what they need in case you run into any mechanical issues – it will be set up in a Symptom – Cause
– Solution type of format, for easy reading. And finally–please let us know if this was helpful for you by leaving comments below! If not…what would you like to see on this blog?

Thursday, May 5, 2011

FEATURED PRODUCT: EXTREME EX7217RCBL BLUE 17 DRAWER ROLLER TOOL CABINET

The Extreme Tools roller cabinet EX7217RC features 17 drawers and is top among the 72" Professional Tool Box Series that have an exclusive patented design. Features include smoother drawer gliding action and drawer latch assembly that has a self-adjusting spring lever action allowing the latch lever to go up into the lock bar for increased security.

A nice feature, visually, with this roller cabinet is there are no spot welds on drawer fronts, hutch or side cabinet. The drawer lock bar assembly uses single cylinder lock design for easy access, and the double steel wall drawer front design offers greater strength to each drawer. The modular drawer design allows drawer configuration to be rotated. There are double channel spot welded support brackets on bottom underside of each drawer that lend to reinforcement as well as prevents sagging.

THIS ROLLCAB COMES WITH STAINLESS STEEL TOP AND FREE SHIPPING!

 

Additional Extreme EX7217RCBL Blue Roller Cabinet Features Include:

• Drawer back panel designed for rigidity to hold more weight without sagging or flexing.
• Top Sub Weldment keeps the top of the box rigid and stable.
• Side cabinet support bracket mounts under toolbox to give added support to side cabinet.
• Tool Box frame design uses 11 gauge steel for stronger chassis and supports the use of heavy duty casters.
• All drawers extend fully.


Extreme EX7217RCBL Roller Cabinet Specifications:

 

• 72”W x 30”D x 46”H
• (6) 6”x 2” casters
• Handle included fits either end
• Extra deep, high gloss powder coat finish
• Drawers with ball bearing glides, all drawers extend fully
• 250 lbs. rating per drawer
• Skid proof drawer liners with top pad made from high density foam
• 17 drawers
• Theft proof lock system
• Shipping weight, 1300 lbs.


The EX7217RC has skid proof drawer liners with top pad made from high density foam. 17 drawers and theft proof lock system are just a few of the incredible features of this 17 drawer roller cabinet.

See Extreme EX7217 Roller Cabinet Specifications.


Visit our website to view this rollcab: http://www.nhproequip.com/p/292/extreme-tools-ex7217rc-roller-cabinet-tool-box

Monday, April 25, 2011

Life After the Franchise

By Jacques Gordon
Published in the April 2011 edition of Professional Distributor Magazine

 After being laid off at 23, Bob Covert decided it was the right time in his life to gamble on going into business for himself. Three years later, after working a territory in the Boston area with a major tool company, Bob took another gamble and moved to the small town of Bow, N.H. to become an independent distributor.

Starting from scratch in a new rural territory without the backing of a major name might seem like the hardest way to succeed in this business, but Bob has some very good resources. His uncle, Clark Heintz, had been a mobile dealer in the area for 34 years when he stepped away from a franchise to open his own independent tool business. He offered his nephew a partnership, and it proved to be a good match. In less than one year Clark had opened a new storefront location and turned the truck over to Bob.
Although the store and the truck are two separate businesses, Clark Heintz Tools & Equipment is one of Bob’s most valuable resources. Bob stocks most of the well-known brands like Ingersoll Rand and OTC, but Clark helps him find other top-quality tools from a wide variety of vendors. And if a customer asks about a tool that Bob has never heard of, Clark’s connections, knowledge and years of experience (and sometimes the tool itself) are only a phone call away.

Bob told us about another resource that’s helped him succeed: technology. He described how the camera on his smart phone helped him find a buyer for his customer’s used tire machine. And even though much of his territory is in a rural area, Bob’s wireless Internet connection is always available.

“It helps me a lot. If a customer asks about a new tool that we don’t know about yet, I’ll Google it.” Even if he doesn’t find the tool right away, at least he gets a good idea of what to look for.

The computer also helps him manage his time. “I have no paperwork at the end of the day, it’s all in the computer and done.”

Franchised versus independence

Having worked as both a franchise distributor and an independent, Bob noted that each has its advantages, but he likes being an independent. One reason is the freedom to choose the tools he stocks on the truck, and with input from Clark and his customers, almost all of those choices have been winners.

Another advantage is the freedom to design his route. He stops at 110 shops per week, every one of them a valuable customer. Bob also spoke highly of a drop-ship program offered by M. Eagles Tools, and some of his other suppliers. If a customer wants a tool that’s not on the truck and the total order exceeds a specific dollar amount, he can call Eagles and they’ll ship it that day.

“(My customer) gets it tomorrow, and I don’t pay overnight shipping. I do that maybe 15 or 20 times a week.”

Bob noted that one of the disadvantages of being independent is the lack of immediate brand recognition.

He said a franchise dealer is almost always accepted the minute the truck shows up. But as an independent, it isn’t the product that sells tools, it’s the person. “They’re buying from me because of me, not because of what I sell.” The proof is in the pudding.

“There are so many brands on this truck they’ve never heard of before, but they trust me.”
“When you first walk into these places it’s kind of formal, just introducing yourself and your products, but after a while they get to know you, trust you. And one day, in the middle of all the locker room talk, without even realizing, you’ve sold $400 worth of stuff…they trust me based on previous experience with me.”

Bob says that experience is a two-way street. “I trust them too. That guy just walked off the truck with a tool and I trust him to pay me. And I know he will. It just comes with spending time with these guys.”

Because it’s fun

As you might expect, Bob describes himself as a “people person” who likes being out and about. His normal day on the truck is ten hours, “but it goes by like,” Bob snaps his fingers, “that, because I’m always busy and I really like what I do. Meeting characters like (his customer), Mike (a very colorful character indeed) is entertaining, and if you can make a living dealing with people like that all day, why not?”

When asked about his accounts receivable, Bob said he doesn’t measure his business that way. “Some guys pay cash in full, so knowing a guy doesn’t have a balance with me is not an indication of how much business he does with me. I look at activity, not balance.

This (other) guy consistently has a bill. When his bill gets low, I know he’s going to buy soon.” Bob also has customers who pay him the same amount every week even if they don’t owe anything, “like a layaway,” Bob said, “because they know they’ll buy something big somewhere down the road.”

Several of his customers are in a large industrial shop that’s been steadily laying people off for months, which makes them reluctant to go into debt for tools that, very soon, they might not need. Bob still stops there right on schedule. “Some of the other dealers don’t stop here anymore. (But) when things turn around, I’m the guy who’s here. Just like I want them to be loyal to me, I have to be loyal in return. That means sticking around when things aren’t going so well.”

When asked about skips, Bob noted that as an independent, he has no network of dealers to help him collect from someone who moves out of the territory. The only option is to make the effort to stay in touch with the customer. However, Bob says he suffers far fewer skips here than he did in Boston, and considers it a non-issue in Bow, N.H.

In the end, it’s hard to tell if there’s a greater difference between being a distributor in the big city versus small town, than there is between being a flag distributor versus an independent.

Either way, it seems Bob Covert has found his own answer, and he’s having fun making money. What’s not to like?

Sunday, April 17, 2011

1st Annual Law Enforcement Memorial Week Poker Run May 22 in Concord NH. ALL BIKES WELCOME!

This self-driven poker run is a fundraiser for both NH State Law Enforcement Memorial Perpetual Care fund, as well as the New England Paralyzed Veteran’s Association Bass Fishing Tournament. Sponsored by the White Mountain Chapter of the Nam Knights Motorcycle Club, the course is as follows: Veteran’s Cemetery in Boscawen, the Epsom Traffic Circle Law Enforcement Memorial, and the State Law Enforcement Memorial in Concord. Return to the Concord VFW for events, raffles, vendors, BBQ, and music!

Clark Heintz will have a booth set up from 9 am to 4 pm- come on over and say hello  and check out his selection of Titan, Handy and Quality lifts!

Where: Concord VFW Post 1631
6 Court Street, Concord, NH

Ride Date: Saturday, May 21, 2011 (rain date: Sunday, May 22, 2011)

Registration: 9-10:30 deadline for hands at VFW 2:30
$25 per bike
$10 for extra hand

1st Prize $200
2nd Prize $100
Enter your BIKES FOR RIDE in bike show entry: $20

Trophies and Prizes for Best in Show 2nd and 3rd Place